Are you guys looking for Civil Engineering MCQ Questions with Answers PDF Free Download as per Civil Engineering new exam pattern? You came to the right page. This may assist you to understand and check your knowledge about the Subjects. Students also can take a free test of the Multiple Choice Questions of Civil Engineering. Each question has four options followed by the right answer. These Civil Engineering MCQ Questions are selected supported by the newest exam pattern.

## Q1. Number of rivets required in a joint, is

(A) Load/Shear strength of a rivet

(B) Load/Bearing strength of a rivet

(C) Load/Tearing strength of a rivet

(D) Load/Rivet value

Answer: (D) Load/Rivet value

## Q2. For steel members not exposed to weather, the thickness of steel should not be less than

(A) 4.5 mm

(B) 6 mm

(C) 8 mm

(D) 10 mm

Answer: (B) 6 mm

## Q3. The equivalent axial tensile load Pe, which produces an average axial tensile stress in the section equivalent to the combined stress due to axial tension P and bending M, at the extreme fibre of the section, is given by (where Z is the section modulus of the section).

(A) Pe = P + MA/Z

(B) Pe = P – MA/Z

(C) Pe = P – Z/MA

(D) Pe = P + Z/MA

Answer: (A) Pe = P + MA/Z

## Q4. If the loaded length of span in meters of a railway steel bridge carrying a single track is 6 m, then impact factor is taken as

(A) 0

(B) 0.5

(C) Between 0.5 and 1.0

(D) 1.0

Answer: (C) Between 0.5 and 1.0

## Q5. When a tension member consists of two channel sections, the allowance for rivet hole is made for two holes from

(A) Each web

(B) Each flange

(C) Each web or one hole from each flange whichever is more

(D) Each web or one hole from each flange whichever is less

Answer: (D) Each web or one hole from each flange whichever is less

## Q6. A riveted joint many experience

(A) Tearing failure of plates

(B) Splitting failure of plates at the edges

(C) Bearing failure of rivets

(D) All the above

Answer: (D) All the above

## Q7. If a pair of angles placed back to back in tension are connected by one leg of each angle, the net effective area of the section, is

(A) a – [b/{1 + 0.35 (b/a)}]

(B) a + [b/{1 + 0.35 (b/a)}]

(C) a – [b/{1 + 0.2 (b/a)}]

(D) a + [b/{1 + 0.2 (b/a)}]

Answer: (D) a + [b/{1 + 0.2 (b/a)}]

## Q8. The maximum permissible slenderness ratio of a member carrying loads resulting from wind, is

(A) 180

(B) 200

(C) 250

(D) 300

Answer: (C) 250

## Q9. The maximum permissible slenderness ratio of a member carrying loads resulting from wind, is

(A) 180

(B) 200

(C) 250

(D) 300

Answer: (C) 250

## Q10. Assuming the values of maximum deviation ΔP and ΔE to be 25% of the computed value of P and E respectively, the minimum value of the factor of safety is

(A) 1.00

(B) 0.67

(C) 1.67

(D) 2.67

Answer: (C) 1.67

## Q11. The average shear stress for rolled steel beam section, is

(A) 845 kg/cm2

(B) 945 kg/cm2

(C) 1025 kg/cm2

(D) 1500 kg/cm2

Answer: (B) 945 kg/cm2

## Q12. The average shear stress for rolled steel beam section, is

(A) 845 kg/cm2

(B) 945 kg/cm2

(C) 1025 kg/cm2

(D) 1500 kg/cm2

Answer: (B) 945 kg/cm2

## Q13. The effective length of a double angle strut with angles placed back to back and connected to both the sides of a gusset plate, by not less than two rivets, is

(A) 0.5 L

(B) 0.67 L

(C) 0.85 L

(D) 2 L

Answer: (C) 0.85 L

## Q14. A beam is defined as a structural member subjected to

(A) Axial loading

(B) Transverse loading

(C) Axial and transverse loading

(D) None of these

Answer: (B) Transverse loading

## Q15. For a rectangular section, the ratio of the maximum and average shear stresses, is

(A) 1.5

(B) 2.0

(C) 2.5

(D) 3.5

Answer:(A) 1.5

**Design of Steel Structures Civil Engineering MCQ and Answers – Set 01****Design of Steel Structures Objective Questions – Set 02****Design of Steel Structures MCQ – Set 03****Design of Steel Structures Multiple Choice Questions – Set 04****MCQ on Design of Steel Structures – Set 05****Civil Steel Structures Design Objective Questions – Set 06****Steel Structures Civil Engineering MCQ Test – Set 07****Steel Structures Design Multiple Choice Tests – Set 08****Multiple Choice Questions on Steel Structure Design – Set 09****Interview Questions on Steel Structures – Set 10****Design of Steel Structures Interview Questions and Answers – Set 11****Important Questions on Design of Steel Structures – Set 12****Civil Steel Structural Engineering MCQ – Set 13****Steel Structures Designing Multiple Choice Questions Test – Set 14****Steel Structures Design Quiz Questions – Set 15****Structural Steel Fabrication Interview Questions – Set 16****Design of Steel Structures Exam Question Bank with Answers – Set 17****Steel Structures Objective type Questions with Answers pdf – Set 18****Civil Engineering Steel Design pdf – Set 19****Civil Engineering Steel Structures Interview Questions – Set 20****Design of Steel Structures Objective Questions and Answers Set – 21**

We hope the given Civil Engineering MCQ Questions with Answers will definitely yield fruitful results. Hope you got enough ideas on the MCQs on Civil Engineering. If you have any queries related to Civil Engineering MCQs Multiple Choice Questions with Answers, drop your questions below and will get back to you in no time.